Implementasi Metode PID Untuk Pengaturan Kecepatan Motor DC Pada Mesin Pencacah Bunga Rosella Kering Untuk Pengolahan Teh Rosella

Authors

  • Delila Cahya Permatasari Universitas Merdeka Malang
  • Nara Agata Abiwindraya Politeknik Negeri Malang
  • Wahyu Dirgantara Universitas Merdeka Malang
  • Nachrowie Nachrowie Universitas Merdeka Malang

DOI:

https://doi.org/10.26905/jasiek.v4i1.8391

Keywords:

PID, Rosella Flower, Speed Sensor

Abstract

In Indonesia Rosella Flowers are used as herbal tea. The process of brewing Rosella Tea is brew 3 – 4 dried rosella petals with 200ml hot water. This brewing process takes a long time from 10 minute or 15 minute. One of way to improved is crushing the rosella flower to little shape with apply PID method. This machine use Atmega32 as controller, speed sensor, laser sensor, and DC Motor as actuator. The working principle of this machine is to stabilize DC motor speed, effective procces is at 900 RPM, in this speed takes 07 minutes 15 seconds to finished the process, and laser sensor has not detected rosella flower to crushing the system will turn off automatically. With percentage overshoot  10.2 %,  settling time 245 seconds, and biggest error of speed sensor is 2.6 % . The reuslt from speed sensor will display at LCD 2*16 to make easily to analysis.

References

D. Cahya, E. Mandayatma, and M. Fauziyah, “Implementasi Metode PI Untuk Pengaturan Suhu Pada Proses Pengeringan Kelopak Bunga Rosella,†J. Elkolind J. Elektron. dan Otomasi Ind., vol. 7, no. 3, pp. 9–14, 2021.

R. Hayati, “Pengaruh Suhu Pengeringan Terhadap Mutu Rosella Kering (Hibiscus sabdariffa),†J. Floratek, vol. 6, no. 1, pp. 1–7, 2011.

H. Maryani and L. Kristiana, Khasiat & Manfaat Rosela. Agromedia, 2005.

D. S. Usman and S. Winarti, “Karakteristik dan Aktivitas Antioksidan Rosela Kering (Hibiscus sabdariffa L.)(Characteristics and Antioxidant Activity Dried Rosella (Hibiscus sabdariffa L.)),†J. Teknol. Pangan, vol. 9, no. 2, 2016.

K. Ogata, Modern control engineering, vol. 5. Prentice hall Upper Saddle River, NJ, 2010.

AnthoniusStephanus, dkk. 2003. STUDI KARAKTERISTIK MOTOR DC PENGUAT LUAR TERHADAP SIKAT. Jurnal Teknik Elektro Vol. 3, No. 1. Fakultas Teknologi Industri, Jurusan Teknik Elektro, Universitas Kristen Petra.

Mangera, Paulus dan Daud Andang Pasalli. 2013. ANALISIS MENGGUNAKAN PEMODELAN UNTUK PENGENDALIAN MOTOR LISTRIK STUDI KASUS MOTOR 1750 RPM/60 HP/240 Volt. Jurnal Ilmiah Mustek Anim Ha Vol.2 No. 3. Fakultas Teknik, Jurusan Teknik Elektro Universitas Musamus Merauke.

Swamardika,Ida Bagus Alit, dkk. 2015. RANCANG BANGUN ROBOT 6WD SEBAGAI ALAT PENDETEKSI KEBOCORAN GAS BERBASIS KOMUNKASI WIRELESS Xbee-PRO SERIES 1 60mW. JTE 1693-2951

Downloads

Published

2022-08-29

Issue

Vol. 4 No. 1 (2022): JUNI 2022

Section

Articles

License

Authors who publish with this journal agree to the following terms:

The journal allow the authors to hold the copyright without restrictions and allow the authors to retain publishing rights without restrictions.

Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-ShareAlike 4.0 International License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

 

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.