Analisis Desain Excavator Bucket Menggunakan Metode Elemen Hingga dengan Material Baja

Authors

  • Agus Dwi Putra Universitas Islam Raden Rahmat Malang, Department of Mechanical Engineering, Faculty of Science and Technology
  • Mojibur Rohman Universitas Islam Raden Rahmat Malang, Department of Mechanical Engineering, Faculty of Science and Technology
  • Abdul Wahab Universitas Islam Raden Rahmat Malang, Department of Mechanical Engineering, Faculty of Science and Technology

DOI:

https://doi.org/10.26905/jtmt.v16i2.4726

Keywords:

Simulasi, Metode Elemen Hingga, Bucket, Baja

Abstract

Penelitian ini bertujuan untuk menganalisis desain bucket excavator dengan metode elemen hingga. Proses desain bucket dilakukan dengan menggunakan software Solidworks 2016. Proses analisis metode elemen hingga dilakukan dengan memanfaatkan software ANSYS 18.1 guna untuk mencari von mises stress, displacement, regangan, dan safety factor pada desain bucket. Hasil menunjukkan bahwa von mises stress yang dihasilkan sebesar 7,72 N/m2 , regangan maksimum pada desain bucket sebesar 2,25 mm, dan regangan terjadi sebesar 2,08835 x106 serta safety factor yang dihasilkan sebesar 3,6.

Author Biography

Agus Dwi Putra, Universitas Islam Raden Rahmat Malang, Department of Mechanical Engineering, Faculty of Science and Technology

Department of Mechanical Engineering, Faculty of Science and Technology

References

Y. Zhang, Y. Li, D. Su, and L. Jin, “Advanced flight control system failure states airworthiness requirements and verification,†Procedia Eng., vol. 80, pp. 431–436, 2014, doi: 10.1016/j.proeng.2014.09.101.

“Analisis kekuatan dan morfologi- Andoko AMSE TEMPLATE Post Review (revisi).†.

M. S. Pham and S. R. Holdsworth, “Change of stress-strain hysteresis loop and its links with microstructural evolution in AISI 316L during cyclic loading,†Procedia Eng., vol. 10, pp. 1069–1074, Jan. 2011, doi: 10.1016/j.proeng.2011.04.176.

C. Seguin, G. Blaquière, A. Loundou, P. Michelet, and T. Markarian, “Unmanned aerial vehicles ( drones ) to prevent drowning ☆,†Resuscitation, vol. 127, no. January, pp. 63–67, 2018, doi: 10.1016/j.resuscitation.2018.04.005.

A. Ahmed, P. Hameed, F. Shaikh, Z. Hussain, N. Hussain, and M. Aslam, “Simulation tools application for arti fi cial lighting in buildings,†Renew. Sustain. Energy Rev., no. August, pp. 0–1, 2017, doi: 10.1016/j.rser.2017.10.035.

R. D. Perez, G. E. Falchini, F. C. Vincente, L. Soares, M. E. Poletti, and H. J. Sánchez, “A new XRF spectrometer using a crystal monochromator and parallel plates beam guides,†Nucl. Instruments Methods Phys. Res. Sect. B Beam Interact. with Mater. Atoms, vol. 440, no. December 2018, pp. 48–53, 2019, doi: 10.1016/j.nimb.2018.11.030.

Andoko and P. Puspitasari, “Finite element analysis of surface tension on piston due to pressure variation,†AIP Conf. Proc., vol. 1778, 2016, doi: 10.1063/1.4965798.

R. V Fedorenko, A. A. Kudryavtsev, V. S, and I. R. Murtazin, “ScienceDirect ScienceDirect ScienceDirect Strength analysis of nuclear power plant structures in case of aircraft Strength analysis of nuclear power plant structures in Paço of aircraft crash impact crash impact modeling of a high a pressure turbine blade,†Procedia Struct. Integr., vol. 6, pp. 244–251, 2017, doi: 10.1016/j.prostr.2017.11.037.

J. W. Langelaan and E. Livne, “Analytic sensitivities and design oriented structural analysis for airplane fuselage shape synthesis,†Comput. Struct., vol. 62, no. 3, pp. 505–519, 1997, doi: 10.1016/S0045-7949(96)00219-2.

L. Witek, “Failure analysis of the wing-fuselage connector of an agricultural aircraft,†Eng. Fail. Anal., vol. 13, no. 4, pp. 572–581, 2006, doi: 10.1016/j.engfailanal.2004.12.029.

T. Itoh, M. Sakane, and K. Ohsuga, “Multiaxial low cycle fatigue life under non-proportional loading,†Int. J. Press. Vessel. Pip., vol. 110, pp. 50–56, Oct. 2013, doi: 10.1016/j.ijpvp.2013.04.021.

V. Infante, L. Fernandes, M. Freitas, and R. Baptista, “Failure analysis of a nose landing gear fork,†Engineering Failure Analysis, vol. 82. pp. 554–565, 2017, doi: 10.1016/j.engfailanal.2017.04.020.

S. Zameer and M. Haneef, “Fatigue Life Estimation of Artificial Hip Joint Model Using Finite Element Method,†Mater. Today Proc., vol. 2, no. 4–5, pp. 2137–2145, 2015, doi: 10.1016/j.matpr.2015.07.220.

Downloads

Published

2022-02-02

Issue

Vol. 16 No. 2 (2020): September 2020

Section

Article

License

Creative Commons License
This work, is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

 

Authors who publish with this journal agree to the following terms:

  • Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License. that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
  • Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
  • Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) before and during the submission process, as it can lead to productive exchanges and earlier and greater citation of published work.