ANALYSIS OF TRACKING HYDRAULIC DESIGNING PROCESS
DOI:
https://doi.org/10.26905/jtmt.v15i2.4774Keywords:
hydraulic tracking, software solid works, stress, strainAbstract
The use of hydraulic systems for various applications supporting work equipment is very widely used because of the nature and strength of the good and easy in its design. Hydraulic tracking can be widely applied in various needs. The principle of this work tool is designed for the release of bearings / mounting on a shaft or a ball bearing house vertically or horizontally. From the results of the hydraulic tracking planning analysis using solid works software, in this simulation to find static nodal stress (the received tensile strength) obtained the highest load is shown in the orange part of the tool with a stress value of 17.49 million N / m2, the load experienced is only 15% of the permitted maximum limit of 24,800,200,000 N / m2.then the strain that occurs in the highest value is shown on a scale with an orange of 0.03946 mm on the upper beam component, that value <1 mm means that the hydraulic frame tracking can be used properly.References
Diana Khairani Sofyan & Syarifuddin. 2015. Perancangan Ulang Tata Letak Fasilitas Dengan Menggunakan Metode Konvensional Berbasis 5s (Seiri, Seiton, Seiso, Seiketsu Dan Shitsuke).
Ulia Ridhani, Aminuddin, Riky Susanto, Adhim Abdul Jabbar, 2010. Rancang Bangun Alat Mounting Dan Dismounting Bearing Dengan Menggunakan Hydraulic Jack.
Nevada J.M Nanulaitta,.Alexander. A. Patty, 2011 Analisa Nilai Kekerasan Baja Karbon Rendah (S35c) Dengan Pengaruh Waktu Penahanan (Holding Time) Melalui Proses Pengarbonan Padat (Pack Carburizing) Dengan Pemanfaatan Cangkang Kerang.
Andika syahrial lazuuardi., 2018, perencanaan sambungan mur dan baut pada gerobak sampah motor. Jurnal Mahasiswa Teknik Mesin Itn Malang
Didi muno irawan, Ganjar Iswantoro, Muhammad Hidayat Furqon, Sri Hastuti4, 2018. Pengaruh Nilai Konstanta Terhadap Pertambahan Panjang Pegas Pada Rangkaian Tunggal, Seri Dan Paralel
Mochamad Irsyadillah, 2016 Laporan Praktikumprogram Cadsolidworks
Riswan Dwi Djamiko, 2008 Modul Teori Pengelasan
Beumer, B.J.M., 1994. Ilmu Bahan Logam., hal 20)
Yusuf bakhtiar, 2015. Analisis buckling terhadap tabung plat tipis menggunakan metode elemen hingga
Sukanto jatmiko, (2005), analisa kekuatan puntir dan kekuatan lentur putar Poros baja st 60 sebagai aplikasi perancangan bahan Poros baling-baling kapal.
Downloads
Published
Issue
Section
License
This work, is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License. that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) before and during the submission process, as it can lead to productive exchanges and earlier and greater citation of published work.
