Analisis Pengaruh Variasi Sudu terhadap Kinerja Kincir Angin Poros Horizontal

Muhammad Fathuddin Noor, Indah Noor Dwi Kusuma Dewi, Alief Muhammad


Indonesia is one of the countries with abundant natural resources that have the potential to become renewable energy at this time, the development of renewable energy is the focus of research because Indonesia is in the middle of the equator which makes more air movement, dependence on fossil fuels can be solved by using wind-powered energy. This study aimed to determine the performance of a horizontal axis windmill with a diameter of 30 cm with variations of 3 blades and 4 blades at a height of 22 meters from the ground. The results of the horizontal axis windmill research that has been carried out in this study can be seen that the wind speed at the 3 blade variation produces the lowest wind speed of 2.0 m/s with a blade rotation of 14.9 rpm and a generator output of 1.12 volts. The highest wind speed is 3.7 m/s with a blade rotation of 28.9 rpm and a generator output of 3.84 volts, while in variation 4 the lowest wind speed is 2.8 m/s with a blade rotation of 29.2 rpm and the generator output is 2.5 volts, while the highest wind speed is 4.3 m/s with a blade rotation of 42.2 rpm and the generator output is 4.9 volts.


wind turbine, horizontal axis, blade variatione.

Full Text:



M. M. M. Saad, et al., “Small Horizontal Axis Wind Turbine under High Speed Operation: Study of Power Evaluation,” J. Phys. Conf. Ser., vol. 914, no. 1, 2017, doi: 10.1088/1742-6596/914/1/012002.

M. S. Gibran and F. Rihlat, “Simulation of Inverse Taper Wind Turbine Blade and Transmission System for Indonesia Wind Condition,” 2015.

S. Nugroho, et al., “Experimental Study on Clark-Y Horizontal Axis Wind Turbine with Winglet,” Proc. - 2018 Int. Conf. Appl. Sci. Technol. iCAST 2018, vol. 1, no. 1, pp. 613–616, 2018, doi: 10.1109/iCAST1.2018.8751587.

G. Dong, J. Qin, Z. Li, and X. Yang, “An Inverse Method for Wind Turbine Blade Design with Given Distributions of Load Coefficients,” Wind, vol. 2, no. 1, pp. 175–191, 2022, doi: 10.3390/wind2010010.

M. Mohammadi, A. Mohammadi, and S. Farahat, “A New Method for Horizontal Axis Wind Turbine (HAWT) Blade Optimization,” Int. J. Renew. Energy Dev., vol. 5, no. 02, Feb. 2016, [Online]. Available:

S. Akhai, P. Srivastava, and S. Sharma, “Developments in horizontal axis wind turbines - A brief review,” J. Crit. Rev., vol. 7, no. 19, pp. 255–260, 2020, doi: 10.31838/jcr.07.19.28.

A. R. Tullah, M. K. Dhiputra, and Soeharsono, “Stress analysis Pada Horizontal Axis Wind Turbine Blade,” POROS J. Ilm. Tek. Mesin, vol. 12, no. 01, pp. 41–45, 2014.

D. Nongdhar and B. Goswami, “Design of Micro Wind Turbine for Low Wind Speed Areas: A Review,” ADBU J. Electr. Electron. Eng., vol. 2, no. 2, pp. 39–47, 2018, [Online]. Available:

B. D. Susilo, G. Jatisukamto, and M. N. Kustanto, “Characteristic Analysis of Horizontal Axis Wind Turbine Using Airfoil NACA 4712,” J. Mech. Eng. Sci. Technol., vol. 3, no. 2, pp. 96–108, 2019, doi: 10.17977/um016v3i22019p096.

S. Widiyanto, S. Pramonohadi, and M. K. Ridwan, “Performance Analysis of Small Horizontal Axis Wind Turbine with Airfoil NACA 4412,” Int. J. Sci. Technol. Manag., vol. 2, no. 1, pp. 347–357, 2015.

H. Eftekhari, A. S. Mahdi Al-Obaidi, and S. Eftekhari, “Aerodynamic Performance of Vertical and Horizontal Axis Wind Turbines: A Comparison Review,” Indones. J. Sci. Technol., vol. 7, no. 1, pp. 65–88, 2022, doi: 10.17509/ijost.v7i1.43161.

P. J. Schubel and R. J. Crossley, “Wind turbine blade design,” Energies, vol. 5, no. 9, pp. 3425–3449, 2012, doi: 10.3390/en5093425.

B. Winarno, I. Basuki, and A. Safi’i, “Design Horizontal Axis Wind Turbine With Three Blades,” JEEMECS (Journal Electr. Eng. Mechatron. Comput. Sci., vol. 1, no. 1, pp. 17–22, 2018, doi: 10.26905/jeemecs.v1i1.2076.



  • There are currently no refbacks.


Universitas Merdeka Malang

Mailing Address:

Jalan Terusan Dieng 62-64 Malang, 65146, East Java, Indonesia
Phone: 081333961913 Fax: (0341) 560836