Rancang Bangun Alat Pengering Eceng Gondok Untuk Bahan Kerajinan Tangan (Menggunakan Metode Tuning Controller Chien Regulator I dan Chien Servo I)
Abstract
Hyacinth is a plant that can be utilized for the manufacture of various types of handicrafts, such as bags, sandals, souvenirs, and other furniture that has high art. In the process of making hyacinth crafts, it is considered in the process of drying. During this time, the hyacinth drying process still using conventional methods, which use solar energy which is dependent on weather conditions. Conventional drying methods relatively need long time, ie 7-10 days. So, that was designed hyacinth dryer that is not dependent on the weather and can be controlled with temperature sensors and weight sensor depend its set point. Hyacinth dryers use heater, blower and air circulation fan. The controller of the drying machine is Microcontroller ATMega 16 with PI Controll methods Tuning Controller Chien Regulator I with Kp = 4,55 and Ki = 0,3 and Tuning Controller Chien Servo I Kp = 2,65 and Ki = 0,156. Hyacinth drying with a dryer need time shorter than using the conventional drying method, ie 12 hours with stabil temperature 60ᵒC . With this dryer can dry 30 stems of hyacinth with initial weight 500g become dry hyacinth with weight ± 60g. Depends on the result of laboratory test, hyacint with dryer produce fiber content, water content, and ash content that good enough.
Keywords
Full Text:
pdfReferences
Atmel Corporation, Datasheet of ATMega16. Atmel Corporation, hal 3
Bakhri, Mohammad Samsul. 2017: “Desain Pengering Eceng Gondok Tipe Batch Sumber Panas Gas Buang Dari Combined Heat and Power”. Skripsi Teknik Mesin dan Biosistem, ITB
Kunto Purbono, Makhmudun Ainuri, Suryandono.2010:”Rancang Bangun Dan Uji Kelayakan Finansial Alat Pengering Mekanis Untuk Pemenuhan Pasokan Eceng Gondok (Eichhornia Crassipes) Sebagai Bahan Baku Kerajinan”.Agritech,Vol. 30, No. 2.
Putra, Rizki Dirgahaya. 2012:”Ekstraksi Serat Selulosa Dari Tanaman Eceng Gondok (Eischornia Crassipes) Dengan Variabel Pelarut”. FT UI.
Rahayuningtyas, Ari, Aidil Haryanto, dan Rina Kumalasari. 2012: “Perancangan dan Uji Performasi Pengering Tipe Rak pada UKM Shan’s Cap Rumoh Aceh”. Prosiding UNISBA
Sari, Puspita Kurnia, Epyk Sunarno, S.ST.,M.T. dan Drs. Irianto M.T. 2016: “Rancang Bangun Alat Pengering Tahu Sebagai Bahan Baku Stik Tahu”. Tugas Akhir D3 Jurusan Teknik Elektro Industri, PENS.
Setiawan, Iwan. “Kontrol PID untuk Proses Industri”. PT. Elex Media Kominfo, Jakarta.
Tumolva, T., J. Ortenero, M. Kubouchi. “Characterization and Treatment of Water Hyacinth Fibers For NFRP Composites” . The 19th International Conference on Composite Materials.
DOI: https://doi.org/10.26905/jtmi.v3i2.1522
Refbacks
- There are currently no refbacks.
Copyright (c)
Index Copernicus International (ICI)
Tools
Jurnal Teknologi dan Manajemen Informatika
Fakultas Teknologi Informasi
University of Merdeka Malang
Alamat:
Jl. Terusan Raya Dieng No. 62-64, Malang, Indonesia, 65146
(0341) 566462
Email: [email protected]
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.